Sound familiar?Cedar Mount
- The call
- On the old wooden door out back, one lock bar hangs loose from a rusted guide and the other is bent at an angle, so the handle turns but the door can still be lifted a hand's width from outside.
You pushed the slide bolt across like always, but tonight it stops short of the slot in the track and springs back. The door is down, the bottom seal is on the concrete, yet the bar and its hole are a finger's width apart.
In plain words
What you have at the end is a lock that behaves like a lock. The bar slides home with a light push and a definite stop, it draws fully back behind the track edge when released so the door can travel, and the outside handle turns with two fingers rather than two hands. Rusted guides have been cleaned or renewed, fixings that had worked loose are anchored in solid material, and the cylinder takes its key without a fight. If an opener shares the door, the two have been set up so they cannot argue, and a note at the wall button says which comes first.
Garage Door Manual Lock Repair · Cedar Mount
How the visit goes
Scene 1
Handle, spindle and the mechanism behind them
The outside handle is turned while the inside of the door is watched. On a healthy lock the spindle rotates the centre body, a cam pushes both bars outward and a spring pulls them back. When the handle turns but nothing follows, the fault is somewhere in that short chain: a spindle that has twisted or sheared, a set screw that has let the inside knob spin free, a cam that has worn round, or a spring that has snapped. The inside cover comes off to see which, and the body is checked for cracks or for pulling away from the door. The exact broken piece decides whether a small part or a complete mechanism is fitted.
Scene 2
Freeing and renewing the bars and guides
Bars that have stiffened are worked loose with penetrating oil and then cleaned back to bare metal, while guides packed with rust are removed, cleaned or replaced with new ones fixed into sound material. A bar that has kinked is replaced rather than straightened, since spring steel that has been bent once takes a set and binds forever after; the new bar is cut to suit the door's width so it reaches through the track with a comfortable margin and retracts fully clear. Both bars are set to the same throw so the door locks evenly on both sides. A light film of silicone on the bars, not grease, finishes the job.
Scene 3
A monthly lock check that takes a minute
Once a month, with the door closed and the opener disconnected, throw the lock and release it a couple of times. You are listening for a clean click, feeling for any new stiffness, and looking at the bar ends to see they still pass through the centre of their slots. Then confirm the bars sit fully back before reconnecting the opener. A bar that has started to drag or a bolt that lands at the edge of its hole is telling you the door or a guide has shifted a little, and a small adjustment at that stage is all it takes. A wipe of the slot edges with a rag keeps rust from getting a start.
In the van
- Centre lock body and return spring
- Carriage bolts and backing plates
- Lock bar guides
- Keyed T-handle lock set
- Spring-steel lock bars
What shapes the quoteInnisfil Garage Door Co.
- Age and pattern of the lock
- Older handles and mechanisms may need a matching-pattern replacement so the existing cutout and bars line up. Sourcing or adapting parts for an uncommon lock shows in the quote.
- Cylinder work and the number of keys
- Rekeying, a new cylinder and each key cut are separate items. Keying the garage to match the house key adds a little pinning time and is listed on its own.
- Rekeying the lock to match your other doors
- Some households want the garage's manual lock to turn with the same key as the house, rather than carrying a separate one. Matching a cylinder to an existing key, or cutting a fresh set for both, is arranged once the existing hardware has been looked at.
FeesSame any hour
Things people wonder
Can a bent lock bar be straightened?
It is better replaced. Lock bars are spring steel, and once one has been bent by an opener pulling against it, it takes a set and tends to bind in its guide or kink again under load. New bar stock is cut to the door's width so the bar reaches through the track with a margin and pulls fully back when released. Both bars are set to the same throw.
Will new holes have to be cut in the track?
Rarely. The slots are already there on most tracks, and a bar that misses one is usually a sign the door or a guide has moved. Restoring the door's closed position and resetting the guide brings the bar back to the existing slot. A new slot is punched only when a lock is added to a door that never had one, or an old slot is badly damaged.
The handle turns but the bars stay put. What has broken?
Something in the short chain between the handle and the bars. The square spindle may have twisted or sheared, the set screw holding the inside knob may have let it spin free, the cam inside the centre body may have worn round, or the return spring may have snapped. The inside cover comes off to see which, and the failed part or the whole mechanism is replaced to suit.
Repair & Maintenance
- Garage Door Tune-UpYou pulled the red cord to lift the door by hand during a power cut and it felt like lifting a car.
- Off-Track Garage Door ResetThere was a loud bang from the garage, then silence.
- Garage Door Panel ReplacementAfter an overnight freeze the door stuck to the slab, the opener strained, and something gave.
- Garage Door Bottom Seal ReplacementWith the door closed and the lights off, a bright line of daylight runs along the floor from one side to the other.
- Garage Door Perimeter WeatherstripAfter a windy night there is a fine ridge of snow on the garage floor along one side of the door, and another across the top step.
Cedar Mountinformation
SimcoeOntario
Garage Door Manual Lock Repair · Innisfil, Bell Ewart, Big Bay Point, Cedar Harbour, Cookstown, Innisfil Park, Killarney Beach, Leonards Beach, Nantyr Park, Stroud, Alcona, Alderslea, Bear Point, Belle Air Beach, Big Cedar Point, Churchill, Crescent Harbour, De Grassi Point, Glenwood Beach, Lefroy, Mooselanka Beach, Peninsular Park, Sandy Cove, Tent City
- Town
- Cedar Mount, Simcoe
- In business
- 21 years
- Hours
- Open 24/7
- Nights, weekends and holidays, same fees
- Phone
- (249) 371-0023
- Visits
- On-site assessment preferred. Request a visit or call.
2021 census: what it means at the door
Every square is one home in a hundred.
- 35 in 100 homes · mixed ages
- 90 in 100 homes · mostly houses
- About 35% of homes in Innisfil were built in 1980 or earlier, according to the 2021 Census.Mixed neighbourhoods often include renovated older houses with a new facade and a garage door that no longer suits it. Choosing a door that ties the renovation together, then installing it plumb and balanced in an older opening, is work we do regularly and enjoy.
- Single-detached houses make up about 90% of homes in Innisfil (2021 Census).In a neighbourhood of houses, each garage door is chosen by the household, so styles vary from one driveway to the next. When it is time for a new door, homeowners pick panel design, windows, colour and insulation freely, and we bring samples to compare against the siding.
Nearby
On-site assessment
Request a visit.
You pushed the slide bolt across like always, but tonight it stops short of the slot in the track and springs back.
(249) 371-0023, open 24/7.